在濟南通風管道的加工過程中，要注意材料的選擇是否合適。針對不同的功能需求，需要選擇不同的材料，采用不同的加工工藝。下面，就和大家一起來看看，濟南通風管道的材料選擇，希望可以給大家?guī)?lái)幫助。

　　In the process of ventilation pipes in Ji'nan, we should first pay attention to the suitability of materials. For different functional requirements, we need to choose different materials and adopt different processing techniques. Next, let's take a look at the material selection of Jinan ventilation pipeline. I hope it can help you.

　　1.對于薄鋼板通風管道內、外表層和內部絕熱材料在通風管道加工中粘接牢固，這是是保證復合材料的基本條件之一。按照規定面積和厚度不僅能延長風管的使用壽命還能增加保溫效果，讓風管得到大程度和好的利用。在這里薄鋼板的選擇也尤為重要。

　　1. It is one of the basic conditions to ensure the safety of composite materials that the insulation materials inside, outside and inside the ventilation pipes of thin steel plates are firmly bonded in the processing of ventilation pipes. According to the prescribed area and thickness, not only can the service life of the duct be prolonged, but also the insulation effect can be increased, so that the duct can be used to the maximum extent and the best. The choice of thin steel sheets is also very important here.

　　2.選擇好的通風管道材料，在通風管道加工過程中，要注意風管的表面是鋁箔材質，為了確保表面層不易損壞，因此要對鋁箔材質作出規定，并且為了保證也規定了風管表層的鋁箔厚度。

　　2. Choose good ventilation duct material, in the process of ventilation duct processing, we should pay attention to the surface of the duct is aluminum foil material, in order to ensure that the surface layer is not easy to damage, so we should make provisions for the aluminum foil material, and in order to ensure safety, we also stipulate the thickness of the aluminum foil on the surface of the duct.

　　通風設備 、通風工程的質量更是決定了家庭和公共場所的環境質量的優劣，人們?cè)谘b修中更加注重通風設備的質量問題。南京通風工程有限公司通風產品和服務在客戶中擁有良好口碑，以產品的質量和信譽占領市場。

　　The quality of ventilation equipment and ventilation engineering determines the environmental quality of family and public places. People pay more attention to the quality of ventilation equipment in decoration. The ventilation products and services of Nanjing Ventilation Engineering Co., Ltd. have a good reputation among customers, and occupy the market with the quality and reputation of products.

　　(1)當風管與風機銜接時，應在進出風口處加軟接頭，其軟接頭的斷面尺度應與風機進出風口共同。軟管接頭普通可采用帆布、人造革等材料，軟管長度不宜小于200，松緊度應適宜，柔性軟管可緩沖風機的振蕩。

　　(1) When the duct is connected with the fan, a soft joint should be added at the inlet and outlet of the fan. The cross-sectional dimension of the soft joint should be the same as that of the inlet and outlet of the fan. The hose joint can be made of canvas, artificial leather, etc. The length of hose should not be less than 200, the tightness should be appropriate, and the flexible hose can cushion the vibration of the fan.

　　(2)當風道與除塵設備、加熱設備等銜接前，應待設備裝置終了后，按理論測繪的圖紙中止預制和裝置。

　　(2) When the air duct is connected with dust removal equipment and heating equipment, the prefabrication and equipment shall be discontinued according to the theoretical drawing after the equipment is finished.

　　(3)濟南通風管道裝置時，進、出風日宜在風道預制時開出洞口，如需在裝置終了的風道上現開風口，其接口處應緊密。

　　(3) When Jinan ventilation pipeline is installed, the inlet and outlet days should be opened when the duct is prefabricated. If the outlet is to be found in the duct at the end of the installation, the interface should be close.

　　(4)當運送含凝結水或含濕量較大的氣體時，其水平管道宜設有坡度，并在低點處接排水管。裝置時風道底部不宜呈現縱向接縫，對底部有接縫處應中止密封處置。

　　(4) When transporting gas with condensate water or high moisture content, its horizontal pipeline should be equipped with gradient and connected with drainage pipe at low point. The longitudinal joint is not suitable for the bottom of the duct, and the sealing treatment should be stopped for the joints at the bottom.

　　(5)對運送易燃、易爆氣體的鋼板風道，在風道銜接法蘭處應裝置跨接線，并與靜電接地網銜接。

　　(5) For steel plate air ducts transporting flammable and explosive gases, a cross connection shall be installed at the flange of the connection of the air ducts and connected with the electrostatic grounding grid.

　　(6)當水平風道高度在4m以上時，裝置人員應系帶。腳手架或移動式支架上的跳板應固定好，跳板寬度應契合規范，在腳手架上的裝置人員宜攜東西袋，避免東西或電鉆等物掉落傷人。

　　(6) when the height of the horizontal airway is above 4m, the installation personnel should fasten the seat belt. The springboards on scaffolds or mobile supports should be fixed well, the width of the springboards should conform to safety specifications, and the installers on scaffolds should carry bags to avoid falling things or electric drills to injure people.

　　(7)雙吊桿支架在風道就位后，應保證橫擔平直，吊桿不改動，雙吊桿受力均勻。

　　(7) After the double suspender bracket is in place in the airway, it should ensure that the cross-arm is straight, the suspender is unchanged, and the double suspender bears uniform force.

　　通風管道好是三個月進行一次清潔，這樣既可以保證平時正常的運轉，還可以延長通風管道的使用壽命。

　　Ventilation pipes should be thoroughly cleaned once every three months, which can not only ensure normal operation at ordinary times, but also prolong the service life of ventilation pipes.

　　以上就是濟南通風管道廠家為大家介紹的山東通風管道加工過程中影響質量的關鍵因素，如果您想了解通風管道安裝的相關資訊，敬請關注我們的網站：http://www.bjhgf.com/，我們將竭誠為您服務，期待您的光臨!

　　These are the key factors affecting the quality of ventilation pipes introduced by Jinan Ventilation Pipeline Manufacturer. If you want to know about the installation of ventilation pipes, please pay attention to our official website: http://www.bjhgf.com/. We will serve you wholeheartedly and look forward to your visit!